Obtaining a Gypsum-Cement Blend, to Be Used as Filling, with Low Hardening Temperature

Gabriela Abad-Farfán; Tito Fernando Muñoz-Cuenca; Paúl Bolivar Torres-Jara; Efrén Vázquez-Silva

doi:doi:10.11648/j.am.20170606.12

| Peer-Reviewed

Obtaining a Gypsum-Cement Blend, to Be Used as Filling, with Low Hardening Temperature

Gabriela Abad-Farfán, Tito Fernando Muñoz-Cuenca, Paúl Bolivar Torres-Jara, Efrén Vázquez-Silva

Published in Advances in Materials (Volume 6, Issue 6)

Received: 7 September 2017 Accepted: 26 September 2017 Published: 7 November 2017

Views: Downloads:

Download PDF

Share This Article

Twitter
Linked In
Facebook

Abstract

When a beam, made of material whose properties would be affected at temperatures above 37°C and with irregular geometry at its ends, is subjected to a bending test; it is necessary to guarantee the stability of its support points to achieve success in the execution of the test. This paper presents a study on the properties of a particular composite material that is used as a filling for certain hollow supports with the aim to provide stability to the ends of the beam when the load is applied. Although the mixture employed reacts exothermically, it does not exceed the maximum temperature level above which the mechanical properties of the constituent material of the beam would be affected. In addition, the strength of the mixture is such that it is able to withstand the compression stresses that are generated during the test.

Published in	Advances in Materials (Volume 6, Issue 6)
DOI	10.11648/j.am.20170606.12
Page(s)	115-121
Creative Commons	This is an Open Access article, distributed under the terms of the Creative Commons Attribution 4.0 International License (http://creativecommons.org/licenses/by/4.0/), which permits unrestricted use, distribution and reproduction in any medium or format, provided the original work is properly cited.
Copyright	Copyright © The Author(s), 2017. Published by Science Publishing Group

Keywords

Hardness, Stress Measurements, Composites

References

[1]	A. Mendoza, “Estudio de las propiedades mecánicas del sistema óseo”, Ingeniería e Investigación, no. 23, pp. 14–19, 1991.
[2]	M. P. Groover, Fundamentos de manufactura moderna: materiales, procesos y sistemas. Pearson Educación, 1997.
[3]	J. Pérez-Ilzarbe, J. Fernández-Carrasquilla, C. Luis-Pérz, "Estudio de la variación, con el calentamiento, de las propiedades mecánicas y de la re-cristalización de la hoja fina de aluminio 1050A". Memorias XI Congreso nacional de propiedades mecánicas de sólidos. Universidad de Cádiz, pg. 115. El Bosque, Sierra de Grazalema; 9 al 12 de septiembre, Cádiz, España, 2008.
[4]	S. C. Cowin and others, Bone mechanics handbook. CRC press, 2001.
[5]	D. Martínez, A. Ortiz, and E. I. Ramírez, “Comportamiento mecánico de hueso femoral porcino bajo cargas a flexión”. Memorias del 14 Congreso Internacional anual de la SOMIM; 17 al 19 de septiembre, Puebla, México, 2008.
[6]	J. Grasa; L. A. González; M. J. Gómez-Benito; J. M. García-Aznar; J. A. Bea; P. J. Laborda: M. Doblaré, “Caracterización mecánica de las propiedades del tejido óseo cortical”. Revista Anales de Mecánica de la Fractura, Vol. 1, Nro. 25, pp. 23-28. 2008.
[7]	J. F. McCabe and A. W. G. Walls, Applied Dental Materials. John Wiley & Sons, 2013.
[8]	“Yesos Dentales”. Krobalto. [Online]. Available: http://krobalto.com/tienda/153-yesos-dentales. [Accessed: 05-Dec-2016].
[9]	J. R. Underwood and M. Chiuini, Structural Design: A Practical Guide for Architects. John Wiley & Sons, 1998.
[10]	S. Crespo-Escobar, Materiales de construcción para edificación y obra civil. Editorial Club Universitario, Alicante, España, 2013.
[11]	B. ASTM, “C472-Standard Test Methods for Phyical Testing of Gypsum”, Gypsum Plasters and Gypsum Concrete, p. 2, 1999.
[12]	H. G. Pulido, Análisis y diseño de experimentos (3a. ed.). McGraw-Hill Interamericana, 2000.
[13]	M. P. Pesántez-Moyano, “Confort térmico en el área social de una vivienda unifamiliar en Cuenca-Ecuador”, Universidad de Cuenca, Tesina previa a la obtención del título Diseño de Interiores, 2012. [Online]. Available: http://dspace.ucuenca.edu.ec/bitstream/123456789/393/1/tesis.pdf
[14]	L. Wierzbicki, “Strength properties of the low-melting-point alloys”, Journal of Achievements in Materials and Manufacturing Engineering, vol. 67, no. 1, 2014.
[15]	H. Hansmann, Compendium Composites. ASM hand book on Polyester resins: ASM International: Ohio, 2003.
[16]	A. Besednjak, Materiales Compuestos. Vol. 100, Univ. Politécnica de Catalunya, 2005.
[17]	D. E. Rodríguez-Félix, J. M. Quiroz-Castillo, T. Del Castillo-Castro, M. M. Castillo-Ortega, L. P. Ramírez-Rodríguez, D. García-Bedoya, T. Mendívil-Reynoso, “Preparación y caracterización de materiales compuestos degradables”. Superficies y Vacío, vol. 28, no. 1, pp. 18-24, 2015.
[18]	A. Rahhali, “Valorización de residuos queratínicos para la obtención de materiales biocompuestos”. Tesis de doctorado. Escola d’Enginyeria de Terrassa. Universitat Politècnica de Catalunya. 2015 [Online]. Available: (http://upcommons.upc.edu/handle/2117/95771)
[19]	R. Salgado-Delgado, A. Olarte-Paredes, A. M. Salgado-Delgado, Z. Vargas-Galarza, E. García-Hernández, E. Rubio-Rosas, T. López-Lara, J. B. Hernández-Zaragoza, “Caracterización eléctrica y térmica de un material compuesto de HDPE/PP y/ CB/CNT”. Acta Universitaria, vol. 26, no. 2, pp. 55-62, 2016. (doi: 10.15174/au.2016.980).
[20]	S. Cardona, D. Peláez, S. Betancourt, “Influencia del tipo de carga sobre el mecanizado de materiales compuestos de poliéster insaturado”. Revista Colombiana de Materiales. no. 5 pp. 42-47, 2013.
[21]	V. W. Álvarez –Arboleda, “Desempeño mecánico de materiales compuestos termoplásticos reforzados con fibras naturales para rotomoldeo”. Proyecto de Grado. Universidad Autónoma de Occidente. Facultad de Ingeniería; Departamento de Energética y Mecánica. Santiago de Cali, Colombia, 2014. [Online]. Available: (http://hdl.handle.net/10614/6894)
[22]	C. Fioretti, A. Galán, R. Moine, M. Varela, P. Varela, H. Mouguelar, S. Gigena, F. Bonino, R. Quinteros, J. Natali, “Características mecánicas dinámicas de la tibia aislada de perro sometida a prueba de impacto”. Int. J. Morphol., vol. 31, no. 2. pp. 562-569, 2013.
[23]	M. León, E. I. Ramírez, O. Ruiz, V. H. Jacobo, “Análisis de la rigidez de un fémur a partir del modelado de un ensayo de flexión en cuatro puntos”. Memorias del XXII Congreso de la SOMIM y XIV Congreso IBEROMAT. Septiembre de 2016 CD. Mérida, Yucatán. México, 2016.

Cite This Article

Plain Text BibTeX RIS

APA Style

Gabriela Abad-Farfán, Tito Fernando Muñoz-Cuenca, Paúl Bolivar Torres-Jara, Efrén Vázquez-Silva. (2017). Obtaining a Gypsum-Cement Blend, to Be Used as Filling, with Low Hardening Temperature. Advances in Materials, 6(6), 115-121. https://doi.org/10.11648/j.am.20170606.12

Copy | Download

ACS Style

Gabriela Abad-Farfán; Tito Fernando Muñoz-Cuenca; Paúl Bolivar Torres-Jara; Efrén Vázquez-Silva. Obtaining a Gypsum-Cement Blend, to Be Used as Filling, with Low Hardening Temperature. Adv. Mater. 2017, 6(6), 115-121. doi: 10.11648/j.am.20170606.12

Copy | Download

AMA Style

Gabriela Abad-Farfán, Tito Fernando Muñoz-Cuenca, Paúl Bolivar Torres-Jara, Efrén Vázquez-Silva. Obtaining a Gypsum-Cement Blend, to Be Used as Filling, with Low Hardening Temperature. Adv Mater. 2017;6(6):115-121. doi: 10.11648/j.am.20170606.12

Copy | Download

@article{10.11648/j.am.20170606.12,
  author = {Gabriela Abad-Farfán and Tito Fernando Muñoz-Cuenca and Paúl Bolivar Torres-Jara and Efrén Vázquez-Silva},
  title = {Obtaining a Gypsum-Cement Blend, to Be Used as Filling, with Low Hardening Temperature},
  journal = {Advances in Materials},
  volume = {6},
  number = {6},
  pages = {115-121},
  doi = {10.11648/j.am.20170606.12},
  url = {https://doi.org/10.11648/j.am.20170606.12},
  eprint = {https://article.sciencepublishinggroup.com/pdf/10.11648.j.am.20170606.12},
  abstract = {When a beam, made of material whose properties would be affected at temperatures above 37°C and with irregular geometry at its ends, is subjected to a bending test; it is necessary to guarantee the stability of its support points to achieve success in the execution of the test. This paper presents a study on the properties of a particular composite material that is used as a filling for certain hollow supports with the aim to provide stability to the ends of the beam when the load is applied. Although the mixture employed reacts exothermically, it does not exceed the maximum temperature level above which the mechanical properties of the constituent material of the beam would be affected. In addition, the strength of the mixture is such that it is able to withstand the compression stresses that are generated during the test.},
 year = {2017}
}

Copy | Download

TY  - JOUR
T1  - Obtaining a Gypsum-Cement Blend, to Be Used as Filling, with Low Hardening Temperature
AU  - Gabriela Abad-Farfán
AU  - Tito Fernando Muñoz-Cuenca
AU  - Paúl Bolivar Torres-Jara
AU  - Efrén Vázquez-Silva
Y1  - 2017/11/07
PY  - 2017
N1  - https://doi.org/10.11648/j.am.20170606.12
DO  - 10.11648/j.am.20170606.12
T2  - Advances in Materials
JF  - Advances in Materials
JO  - Advances in Materials
SP  - 115
EP  - 121
PB  - Science Publishing Group
SN  - 2327-252X
UR  - https://doi.org/10.11648/j.am.20170606.12
AB  - When a beam, made of material whose properties would be affected at temperatures above 37°C and with irregular geometry at its ends, is subjected to a bending test; it is necessary to guarantee the stability of its support points to achieve success in the execution of the test. This paper presents a study on the properties of a particular composite material that is used as a filling for certain hollow supports with the aim to provide stability to the ends of the beam when the load is applied. Although the mixture employed reacts exothermically, it does not exceed the maximum temperature level above which the mechanical properties of the constituent material of the beam would be affected. In addition, the strength of the mixture is such that it is able to withstand the compression stresses that are generated during the test.
VL  - 6
IS  - 6
ER  -

Copy | Download

Author Information

Gabriela Abad-Farfán

Facultad de Ingeniería Mecánica, Universidad Politécnica Salesiana, Cuenca, República del Ecuador
Tito Fernando Muñoz-Cuenca
Paúl Bolivar Torres-Jara

Facultad de Ingeniería Mecánica, Universidad Politécnica Salesiana, Cuenca, República del Ecuador
Efrén Vázquez-Silva

Facultad de Ingeniería Mecánica, Universidad Politécnica Salesiana, Cuenca, República del Ecuador

Download PDF

Sections

Plain Text BibTeX RIS

APA Style

Gabriela Abad-Farfán, Tito Fernando Muñoz-Cuenca, Paúl Bolivar Torres-Jara, Efrén Vázquez-Silva. (2017). Obtaining a Gypsum-Cement Blend, to Be Used as Filling, with Low Hardening Temperature. Advances in Materials, 6(6), 115-121. https://doi.org/10.11648/j.am.20170606.12

Copy | Download

ACS Style

Gabriela Abad-Farfán; Tito Fernando Muñoz-Cuenca; Paúl Bolivar Torres-Jara; Efrén Vázquez-Silva. Obtaining a Gypsum-Cement Blend, to Be Used as Filling, with Low Hardening Temperature. Adv. Mater. 2017, 6(6), 115-121. doi: 10.11648/j.am.20170606.12

Copy | Download

AMA Style

Gabriela Abad-Farfán, Tito Fernando Muñoz-Cuenca, Paúl Bolivar Torres-Jara, Efrén Vázquez-Silva. Obtaining a Gypsum-Cement Blend, to Be Used as Filling, with Low Hardening Temperature. Adv Mater. 2017;6(6):115-121. doi: 10.11648/j.am.20170606.12

Copy | Download

@article{10.11648/j.am.20170606.12,
  author = {Gabriela Abad-Farfán and Tito Fernando Muñoz-Cuenca and Paúl Bolivar Torres-Jara and Efrén Vázquez-Silva},
  title = {Obtaining a Gypsum-Cement Blend, to Be Used as Filling, with Low Hardening Temperature},
  journal = {Advances in Materials},
  volume = {6},
  number = {6},
  pages = {115-121},
  doi = {10.11648/j.am.20170606.12},
  url = {https://doi.org/10.11648/j.am.20170606.12},
  eprint = {https://article.sciencepublishinggroup.com/pdf/10.11648.j.am.20170606.12},
  abstract = {When a beam, made of material whose properties would be affected at temperatures above 37°C and with irregular geometry at its ends, is subjected to a bending test; it is necessary to guarantee the stability of its support points to achieve success in the execution of the test. This paper presents a study on the properties of a particular composite material that is used as a filling for certain hollow supports with the aim to provide stability to the ends of the beam when the load is applied. Although the mixture employed reacts exothermically, it does not exceed the maximum temperature level above which the mechanical properties of the constituent material of the beam would be affected. In addition, the strength of the mixture is such that it is able to withstand the compression stresses that are generated during the test.},
 year = {2017}
}

Copy | Download

TY  - JOUR
T1  - Obtaining a Gypsum-Cement Blend, to Be Used as Filling, with Low Hardening Temperature
AU  - Gabriela Abad-Farfán
AU  - Tito Fernando Muñoz-Cuenca
AU  - Paúl Bolivar Torres-Jara
AU  - Efrén Vázquez-Silva
Y1  - 2017/11/07
PY  - 2017
N1  - https://doi.org/10.11648/j.am.20170606.12
DO  - 10.11648/j.am.20170606.12
T2  - Advances in Materials
JF  - Advances in Materials
JO  - Advances in Materials
SP  - 115
EP  - 121
PB  - Science Publishing Group
SN  - 2327-252X
UR  - https://doi.org/10.11648/j.am.20170606.12
AB  - When a beam, made of material whose properties would be affected at temperatures above 37°C and with irregular geometry at its ends, is subjected to a bending test; it is necessary to guarantee the stability of its support points to achieve success in the execution of the test. This paper presents a study on the properties of a particular composite material that is used as a filling for certain hollow supports with the aim to provide stability to the ends of the beam when the load is applied. Although the mixture employed reacts exothermically, it does not exceed the maximum temperature level above which the mechanical properties of the constituent material of the beam would be affected. In addition, the strength of the mixture is such that it is able to withstand the compression stresses that are generated during the test.
VL  - 6
IS  - 6
ER  -

Copy | Download